We will reply to your message within an hour.
Knockouts allow you to modify these boxes to fit your application.
These boxes come ready to use with receptacles and/or light switches installed.
Close off unused outlets.
Add depth to your outlet box.
Close off unused switches.
Add depth to your switch box.
Add depth to octagonal outlet boxes.
With built-in threaded connections, these boxes allow you to attach conduit without using fittings.
Mount these boxes to the outside of an enclosure to access a programmable logic controller or other networked device without opening the enclosure.
Use the built-in connections to attach conduit without using fittings.
Designed for commercial use, these heavy duty boxes have thick, rigid walls.
These boxes have an open back to accommodate extra-deep low-voltage devices.
Mount these boxes on the surface of your wall in areas where you can't create a recess.
Build your own outlet box or replace a damaged box.
These boxes come ready to use with receptacles installed.
Exposure to rain, snow, and wet conditions won't damage these corrosion-resistant boxes.
These corrosion-resistant covers can withstand rain, snow, and wet conditions without being damaged.
Keep the cover closed during operation to completely shield the outlet and plug from rain, snow, and wet conditions.
Add depth to your weatherproof outlet box.
These corrosion-resistant boxes are built to withstand exposure to rain, snow, and wet conditions.
Rain, snow, and wet conditions won't damage these corrosion-resistant covers.
Give switches and outlets a finished look.
Close off unused switches and outlets.
Keep switches and outlets under cover for protection from dust and dirt. These stainless steel plates resist corrosion and have a sealing gasket to keep out moisture.
Pair wall plates and adapters to create a custom cover for existing receptacles and switches to give them a rejuvenated look, no rewiring required.
Snap end and center sections together to create your own two-device or wider wall plate.
Cover existing outlets and switches for a refreshed appearance, no rewiring necessary.
A large angled opening provides an exit point for cords that run behind walls.
Create various data connector configurations by choosing adapters to snap into the ports in these wall plates.
Often used in offices and workstations, these outlet strips power multiple devices from a single wall outlet.
Save energy by automatically turning off unused outlets. The master outlet controls five outlets and shuts off power to the other outlets when a device plugged into the master is turned off.
Separately control each device plugged into these strips—each outlet has its own power switch.
The power switch to these outlet strips is on a 44" long cord, so you can control power even when the strips are in hard to reach places, such as under a desk.
Keep personnel safe from electric shock with ground fault protection.
Filters between the outlets on these strips protect computers and other sensitive equipment from external signals that interfere with the equipment’s performance.
With a rubber housing, these outlet strips withstand drops and other impact.
A combination of an outlet box, cord, and duct, these outlet strips minimize tripping hazards and protect the cord from damage.
Also known as hospital-grade outlet strips, these outlets have an extra-tight fit to prevent plugs from detaching. They are marked with a green dot.
These curved outlet strips clamp onto a pole or table leg.
Snap these wall plates onto flush-mount outlet strips to secure the outlet strip in a cutout.
Connect multiple devices from a single outlet.
Create a permanent outlet system without opening walls. These outlet strips mount to a wall with clips and hardwire to an existing electrical system.
Install these extra-long strips onto the frame of an electrical cabinet.
Mount these strips into standard 19" wide electronics racks and enclosures.
Mount these outlet strips to a desktop or workbench with the mounting hardware, or set them on a surface.
Bring power to workstations that are not near a wall—these poles mount from the ceiling.
Plug these portable distribution boxes into a power source, such as a generator, to power equipment when electricity is not available. They're also known as spider boxes.
In addition to an outlet on the end, these cords have multiple inline outlets.
Insulated to resist water, oil, and solvents, these cords withstand dirty and greasy environments.
Designed for indoor use, these cords are often used to power appliances.
Power multiple devices with one extension cord.
Thick insulation protects the internal wires of these cords, so they can be used in high-traffic areas and over rough surfaces.
Prevent damage to electronic equipment caused by spikes in current. Mount these receptacles to DIN rail.
Attach these general purpose receptacles to DIN rail to bring power closer to where you need it.
Keep personnel safe from electric shock by adding ground fault protection to all outlets on the same circuit. These receptacles mount to DIN rail.
For use with washdown receptacles, these outlet boxes withstand corrosive and washdown environments.
Immediately cut power with a single push.
Mount these switches in an outlet box. Also known as palm-button switches, they have a large button that makes them easy to use even while wearing gloves.
Reset fire panels, or open electromagnetic locks, electric strikes, and automatic door openers. These switches require a key to turn circuits on or off, limiting access and preventing accidental activation.
Charge multiple devices at once.